Page 12 - Combined_31_OCR

ORDERING INSTRUCTIONS: (Order by Part Number, NOT Index Number). j Find the corresponding part that you wish to
A replace on the exploded view illustration and
ORDER FROM: Your truck dealer or the Bostrom Distributor for your note its index number, refer to index list
area. A below and record part number, quantity required
and description. Replaceable components of an
BE SURE TO SPECIFY: Serial number (see exploded view for A assembly are indented under that assembly,
location of serial number), part number and description as indicating that they can be ordered separately or will
listed below and quantity required.
be included if the assembly is ordered.

New Qty. Description
Part No. Index No. Part No.
1 27901-1 BASE ASSY., w/bearings
14 23838-801 BEARING, Flanged
2 25770-806 OUTER LEVER ASSY., w/Pins and Bearings
3 26020-801 BEARING, Flanged
4 25779-801 PIN DRIVE
5 34044-1 CENTER LEVER ASSY. KIT — Includes torsion bar set and weight indicator.
6 27191-801 BEARING, Housing, L.H.
7 25775-801 BEARING, Housing, R.H.
60 31015 RIDE LEVEL INDICATOR
8 25690-801 ROLLER AND BEARING, ASSY.
9 25777-801 STUD
10 25989-801 SNAP RING
11 26988-801 WASHER, Plain
12 *353019-801 LOCKWASHER, 3/8 SAE Med.
13 *350003-801 NUT, Hex., 3/8-16 (UNC-2B)
15 353042-801 WASHER, Plain 7 Ga. x % x %
16 60470-1 SHOCK LEVER ASSY. KIT
17 SHOCK LEVER ASSY.
18 25790-802 HINGE SHAFT, Shock
19 25789-802 HINGE SHAFT, Shock, Rear
20 22525-801 ROLL PIN
21 60475-1 SHOCK ABSORBER ASSY. KIT
18 25790-802 HINGE SHAFT, Shock
22 SHOCK ABSORBER ASSY., w/bearings
23 60477-1 BEARING KIT (Shock Absorber)
18 25790-802 HINGE SHAFT, Shock Below serial No. 68,900
24 22506-801 BEARING, Flanged order both left and right
25 27159-802 RETAINER (T-Bar) hand side panels.
28 28149-806 SIDE PANEL ASSY., L.H.
61153-1 27 25780-802 TORSION BAR SET (2 bars per set)/—From seat serial No. 68,300
26 27160-802 YOKE (Adjuster) order new part No.
29 28150-808 SIDE PANEL ASSY., R.H.----------
30 28776-801 ADJUSTER SCREW AND LEVER ASSY.
35 26445-802 SPRING (Tension)
38 26827-801 WASHER, Plain
39 23308-801 THRUST BALL BEARING
40 25810-801 ADJUSTER PIN
41 353031-801 WASHER, Plain, % Thick x % x VA
42 27193-801 LUB. FITTINGS (%2 Shank)
44 25778-801 LUB. FITTING Shank)
45 30064-801 ROLLER (Nylon)
46 *353043-801 WASHER, Plain, SAE, Zinc Plated
47 *353024-801 LOCK WASHER, % SAE, Med. Zinc Plated
48 .*351119-801 NUT, Hex, Xa-18 (UNC-28) Zinc Plated
51 32118-1 ADJUSTER KIT— Includes right and left hand rails and latch wire.
52 *351152-801 CAP SCREW, %-18 x % Lg. Fi 11 ister-Phi 11 i ps Zinc Plated
34031-801 53 27194-801 BUMPER, Bottom (53A) and Topping (53B). Below seat serial No. 53313,
order P/N 34031-1 which includes bumpers and retainer clips.
25998-503 (Black) 25998-501 (Gray) 1 SEAT CUSHION ASSY. — Includes pan, cover, pad and fastener clips.
25998-502 (Black) (JI CJl (JI (JI C T > (JI (JI 25998-500 (Gray) 1 1 COVER ASSY. KIT, Seat Cushion — Includes cover, pad and fastener clips.
PAN ONLY, Seat Cushion
28630-501 (Gray)
28630-503 (Black) > 25996-806 1 BACK CUSHION ASSY. (Space Saver) — Includes pan, cover, pad and fas­
tener clips.
28630-502 (Black) 57 28630-500 (Gray) 1 COVER ASSY. KIT, Baek Cushion (Space Saver) — Includes cover, pad
and fastener clips.
tn er (O 28346-802 FASTENER CLIP, Cushion
PAN ONLY, Back Cushion
27040-801
STANDARD SEAT ASSEMBLIES t
26658-1 VIKING with Space Saver Back Cushion w/o Risers (Black Trim)
26657-1 VIKING with Space Saver Back Cushion and Universal Risers (Black Trim)
The descriptions and specifications contained in this manual were in
effect at the time the book was approved for printing. (JOP Bostrom
Commercially available at hardware outlets. Division, whose policy is one of continuous improvement, reserves
4
the right to discontinue models at any time, or to change specifica­
tions or design, without notice and without incurring obligation.